Pre 30 Tractor and Engine Parts #1
This auction has a bit everything from Headlamps, Whistles, Igniters, Magneto and everything in between.
Staggered ending auctions allow items to end on an individual lot level. Time extensions will happen if bidding is still active. When bidding has stopped on the lot the lot will close.
Pair of wheels
Nice small size for display, turns freely
Nice original cab with tag, Rare!!!
Full set of castings for a scale model friction drive tractor. Based off of an original Morton chassis. These are unmachined castings. This is setup for a 6hp International Famous Engine - An finished example is included in the photos.
Nice original clutch pulley. Measures 24" & 10.75"
Original cart for International engine! Repainted
Nice project with additional raw castings
Nice clutch pulley. Measures: 19.5" and 6.5"
Measures: 19" long and 22" in diameter. Untested. Bracket is 10" front to back and 14" side to side.
18.5"x13"x20.5" General electric company. Cat:166012, Form: L1. Untested.
RR Record #: S-11212-A 9"x16"x15" 4 3/4" on center for bracket front to back 12.5" on center for bracket left to right.
IHC Fantasy Etching- Made by Lee Lights Model BL130. 24" tall 14" width 19" from bracket to bracket
Acetylene light- has burner and perfect reflector with wooden handled. 14" diameter with triple lens. High quality restoration.
Approx. 12" bell. Clapper is good! Is approx. 17" tall on wooden skid.
11.75" bell. Reads Graham White- Salem 506 Double Acting Clapper. Set up to be used with air compressor. Untested.
Clapper is intact.
5" in diameter. 31" tall.
23" tall. Is marked Northern Pacific with threaded flange base.
Measures: 21" long & 5" in diameter.
12" tall 2.5" in diameter.
10" x 1.5" d
Measures: (1) 8.5" tall and 2" in diameter. (1) 7" tall and 1.5" diameter.
14" in diameter. Reads to 300lbs. Chrome plated bezel with no visible dents.
Brass bezel and silver plated face with incised numerals.
Nickel plated- nice overall condition.
Marked Nash Engineering Co. South Norwalk CT. Nice brass bezel- no visible dings.
Brass bezel. Reads up to 160lbs.
Nice bezel with no visible dents. Rear fitting. 7.5 Incised numerals. Marked Carbondale Machine Co. Crack in glass.
8.5 inches. 200lb gauge. Has mounting ring.
Brass bezel-- 150lbs.
Made by Manning Maxwell and More Inc. Ashcroft. Comes with original weights and fittings. Nickel plated. Has original sign with directions in lid.
Includes: 31 brass weights.
Appears to be complete. Has original documentation.
Has gas spark an choke throttles. Oil and amperage gauges. Has Eisemann key. Measures 7"x12"x .25" thick.
SN: 35914 Model # 330BB Missing 1 tail pipe and nut.
Stamped 'special' SN: Not legible. Model #:330BB
Missing 1 nut. SN:388524 Model #:AA21
Measures: 5"x 14.5"
Loose- needs new friction wheel. 5 bar.
Will fit IHC 8-16 & 10-20 Moguls.
10 volt. Glass cover. Tested and runs smoothly. Has some nickel plated parts.
In leather case. Nickel plated. American Schaefer and Budenburg.
Brass base. Needs leather friction wheel.
Early engine friction drive flywheel ignitor ignition generator. Stated to motor along as it should when wired to a 12 volt battery. Has reproduction cast brass brush cover.
SN:125301 Gear drive. Brass base Loose!
With gear for 1HP Mogul engine.
Mounting holes are good. Will spark when wires are held against gear teeth when being tested.
SN:2977140 Type AB33FD-1
22" tall. Looks to be complete with wooden knobs and polished brass. 1/2" NPT.